[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Winding primary



Original poster: "Malcolm Watts" <m.j.watts-at-massey.ac.nz> 

On 10 Mar 2004, at 19:07, Tesla list wrote:

 > Original poster: "Luke" <Bluu-at-cox-dot-net>
 >
 > With the low coupling all of the energy does not transfer from the pri
 > to the sec.  Does the amount that does not transfer just feed back
 > into the cap as the magnetic field collapses?  So the low coupling
 > doesn't equate to losses?  Instead of losses it just transfers the
 > energy slower?

It gives the primary gap and other resistances more time to waste
power by transferring more slowly. The magnetic field that does not
couple to the secondary couples to the primary as well as other
conductive objects and there is some radiative loss going on as well.
The gap is the most lossy component in most primary systems.

Malcolm


 >
 > I am just checking I think this is true but wanted to confirm.
 >
 > Thanx
 >
 >
 > Luke Galyan
 > Bluu-at-cox-dot-net
 > http://members.cox-dot-net/bluu
 >
 > -----Original Message-----
 > From: Tesla list [mailto:tesla-at-pupman-dot-com]
 > Sent: Tuesday, March 09, 2004 8:45 PM
 > To: tesla-at-pupman-dot-com
 > Subject: RE: Winding primary
 >
 > Original poster: Terry Fritz <teslalist-at-twfpowerelectronics-dot-com>
 >
 > Hi Luke,
 >
 > Simply think of "loss" as how "hot" it gets.  The streamers are hot
 > and account for about 70% of the energy of a coil.  The gap is hot and
 > accounts for the other about 30%.  The leads of the caps are pretty
 > darn cold ;-)))  and they account for a little more than 0% percent
 > loss....
 >
 > Cheers,
 >
 >           Terry
 >
 >
 > At 09:34 PM 3/9/2004, you wrote:
 >  >Two strings in parallel (such as what I am building) still seems
 >  there >is little cross sectional area.  Are you saying that because
 >  the leads >are so short they offer almost no resistance like say the
 >  ohm per 1000 >feet of wire charts would indicate? > >thanx > >Luke
 >  Galyan >Bluu-at-cox-dot-net >http://members.cox-dot-net/bluu > >-----Original
 >  Message----- >From: Tesla list [mailto:tesla-at-pupman-dot-com] >Sent:
 >  Tuesday, March 09, 2004 7:22 PM >To: tesla-at-pupman-dot-com >Subject: RE:
 >  Winding primary > >Original poster: Terry Fritz
 >  <teslalist-at-twfpowerelectronics-dot-com> > >Hi Luke, > >The key is those
 >  leads are very short and normally in parallel.  The >loss >from the
 >  skinny leads is trivial.  They do make those caps with big >strap
 >  >leads, but the cost is stunning for the special order... > >Cheers,
 >  > >          Terry > >At 07:48 PM 3/9/2004, you wrote: > >On the note
 >  of not needing a big honkin primary coil..... > >I was starting on
 >  building my MMC the other day and it hit me that we > >talk about all
 >  this high power and current in the tank circuit and
 > use
 >  >a
 >  > >heavy gauge for the primary when in reality as far as wire size
 >  goes >the > >weak link seems to be the leads coming from the caps in
 >  the MMC.
 > They
 >  > >are so small compared to what is suggested for the primary.
 >  > >
 >  > >
 >  > >Luke Galyan
 >  > >Bluu-at-cox-dot-net
 >  > >http://members.cox-dot-net/bluu
 >  > >
 >  > >-----Original Message-----
 >  > >From: Tesla list [mailto:tesla-at-pupman-dot-com]
 >  > >Sent: Tuesday, March 09, 2004 5:56 PM
 >  > >To: tesla-at-pupman-dot-com
 >  > >Subject: Re: Winding primary
 >  > >
 >  > >Original poster: "Antonio Carlos M. de Queiroz"
 > <acmq-at-compuland-dot-com.br>
 >  > >
 >  > >Tesla list wrote:
 >  > >  >
 >  > >  > Original poster: Gregory Hunter <ghunter31014-at-yahoo-dot-com>
 >  > >
 >  > >  >... Finally, if
 >  > >  > the first primary looks like a nightmare, discard the
 >  > >  > Cu tube and try again. You're only out $12 or
 >  > >  > so--chicken feed in this cash-intensive hobby!
 >  > >
 >  > >And note that unless your coil is a really big thing, there is no
 >  > >technical reason to use tubing for the coil. Any reasonably thick
 >  > >wire is more than enough. All my primaries were made with #18 >
 >  >solid wire (Ok, a 5 kV x30 mA NST doesn't give a lot of power). >
 >  >http://www.coe.ufrj.br/~acmq/tesla/tefpprim.jpg > >Not a work of
 >  art, but cheap and works. > > > >Antonio Carlos M. de Queiroz
 >
 >
 >