[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] bipolar coil



Bart,

Yes, this is a twin setup with two separate identical secondaries, each with its own topload and ground, positioned vertically a distance apart from each other. This is not a traditional bipolar design with one long secondary positioned horizontally with a primary positioned around its center.

The lead inductance is a killer, but with the bases of the secondaries mounted 36" on center apart, there is only so much I can do to shorten the lead length. My 48" estimate might be a little on the optimistic side. 

I think the main problem here is that I don't quite understand why the recommended LTR cap for the srg is 2.6x resonance. I understand why I don't want to be too close to resonance but I don't quite get why a synchronous rotary gap causes the need for it to be so much larger than with a static gap, or how performance would be effected by decreasing the cap size, so I just stuck close to the recommended figure. 

If I can just use a smaller cap, then the primary turns problem wouldn't be such an issue, but I would like to understand this better before I start tweaking this figure.
 


bartb <bartb@xxxxxxxxxxxxxxxx> wrote: Hi Kris,

Using the 9/60 NST, SRSG LTR is .046uF. Doubling this for the bipolar 
situation is just too much cap (resulting in less than 1 turn). 
Remember, you don't have to go this big with the cap. Say you use the 
1.6 x Cres value which is .0265uF. Thus doubling this you would input 
.053uF for the cap size. When you tune, you'll end with 2.2 turns per 
coil. Thus each coil will have 1.245uH for a total of 2.49uH with the 
.0265uF cap. Each coil will be resonant at 410kHz (assuming each twin is 
2.375" x 11.5", 975 turns, 30 awg, with 3"x12" toroid).

I'm not trying to suggest that 0.0265uF is the value to use, but simply 
to show that a smaller cap size is needed so that you can transfer more 
turns to each primary coil. The above assumes 1.6uH of lead inductance 
(I used the full 48" lead inductance considering the model needs to see 
all of it). If you can reduce the wiring to bare minimum, you can then 
transfer that inductance into the primary turns as well. Right now, it 
is being shared with the primary and it is a significant at 36% of the 
total inductance.

For clarification: Your original post identifies twin coils, not a 
bipolar coil. Is this correct? You were using the program in a bipolar 
configuration simply to try to model the situation? That's how I 
interpreted.

The reason I ask, is if this were actually a bipolar coil, I would model 
it very differently.

Take care,
Bart

Kris Grillo wrote:
> I have wound the coils and put about 25 coats of poly on them, and made the toploads. In fact, everything is done except for the primaries. 
>
> I do realize that 1350VA is a huge amount of power for such a small coil. I think I got a little carried away. Originally I was going to use just one of the 60mA transformers, but then I found another one real cheap, so I bought it. I had another 30mA sitting on the shelf and figured what the hell, lets make a monster of a small coil. I think I'll just stick with the original plan of 60mA.
>
> Bart, I tried inputing just one of the twins and doubling the cap size. I get a geometry error, less than one turn primary. I also tried it with 120mA, 90mA, 60mA and 30mA, all with the same results. This was with 2x the recommended LTR cap size for a synchronous rotary gap for each of the currents. I tried it with double 2x resonant also, with the same results. I haven't tried tweaking the primary dimensions, except for spacing the coupling. Any suggestions?
>   
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla


       
---------------------------------
Be a better friend, newshound, and know-it-all with Yahoo! Mobile.  Try it now.
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla