Re: [TCML] New 3.5" Coil - A kick in the right direction please!

["DC Cox" <resonance@xxxxxxxxxxxx>]

A few more tips for Grant:

(1) Use JAVATC for your entire design --- Bart's program is deadly accurate.

(2) Use a 4.5:1 height/dia ratio.  Select the largest coilform size you can
tolerate, then multiply by 4.5 to get the correct winding length.

(3) Use a topload that is 2 to 3 times the dia. of the sec coilform.

(4) Use an efficient sparkgap for good quenching (hyperbaric gaps work
excellent with most NST powered coils.  Sparkgap shut off is particularly
important to
prevent sec - primary excessive energy translations.  The idea is to keep
the energy in the sec as much as possible.

(5) Use approx 1,200 turns on the sec.     divide the winding length by
1,200 to get the correct wire dia.

(6) Then, select wire size from a wire chart --- use only double build
insulated wire (very good insulation).

(7) Coat your sec winding with 4-5 coats of Dolph's AC-43 or equivalent.

(8) Use Antonio's very simple 555 oscillator to do the initial tuning to get
the best possible setting without guessing.

(9) Use my RF probe tuner to adjust coil for maximum output voltage.

(10) John Freau's equation of D (inches) = 1.4 x SQR power (watts) will give
you an accurate output estimate.  Yes, John uses 1.7 but
he also used very large (40") sec diameter.   I use 1.4 and it's very
accurate.

Follow these rules, use good primary caps, and your coil will perform
excellent on the first fire-up.

Regards,

Dr. Resonance




On Fri, Sep 19, 2008 at 8:48 PM, bartb <bartb@xxxxxxxxxxxxxxxx> wrote:

> Hi Grant,
>
> Something that caught my eye is that you "want" the secondary wire length
> at 1/4 wave. I hope this is only a "want". A coil of course does not require
> this for best spark performance. If you "really" want the secondary wire
> length to be 1/4 wavelength (such as antenna theory, radio circuits, etc.)
> then realize you can't use a top load. A top load will capacitively load the
> secondary significantly and change the distributed capacitance affecting the
> coils frequency (far from the wire length). Spark propagating coils are
> tuned to their fundamental frequency which may be close or far away from the
> 1/4 wire wavelength situation. The wire length has no bearing on the
> resonant frequency. The resonant frequency of a coil is a composite of all
> the capacitances (objects) which affect the coil as well as the inductance.
> But it doesn't stop at simply object capacitances causing the change. With
> increasing frequency and with coil geometry (h/d ratio, spacing ratio,
> etc..), the currents along the length of the coil are also affected. This
> causes variations in inductance along the coil. If you could measure the
> inductance of each turn say on a 1000 turn coil, not all turns would measure
> the same inductance (even though the wire size, geometry, and length are the
> same). The current affects the emf and thus mutual inductance to adjacent
> turns, which in turn affects the inductance of each turn itself. If the
> current varies, so does the inductance. But if you calculate those currents
> along the form at the fundamental and lump the inductances, you'll find the
> "real" inductance at the fundamental frequency (which is different than say
> a DC inductance or even 1kHz LCR inductance measurements). By the word
> "real", I mean the inductance which is affecting the fundamental frequency.
> This situation also affects the 1/4 wave wire length precursor because of
> the inductance at high frequency (which is any frequency above DC which
> adversely affects the inductance). So even our lowish frequency 100kHz coils
> will have an effective inductance at the fundamental which will be different
> than the wire inductance.
>
> By all these "words", I'm simply saying that to actually make a 1/4 wave
> wire length equal to the fundamental is no small task. Wheeler and Medhurst
> equations won't help here. To do this, you really need a bare secondary by
> itself. Even a primary coil is seen as an object to the secondary that will
> change the situation. Coil height to ground, walls, and miscellaneous
> objects do the same. But to do it in a dual-resonant coil situation can only
> be done best with just those 2 coils and nothing else. Even using a little
> small sphere as a top load (to reduce Ctop) affects the coil a tad. It can
> be done that way, but if you want a spark performing coil, then this isn't
> the way to go about it. It causes many limitations to the coil design which
> affects performance.
>
> If we ignore the 1/4 wave length wire theory, then we really only need to
> worry about the fundamental frequency regardless of the objects on or around
> the coil. This type of design makes for good sparking coils because we now
> have freedom to play with primary LC values to match whatever fundamental
> frequency the secondary coil ends up at.
>
> So it's hard to give advice. If your set on "1/4 wave wire length" as a
> precursor, then you have your work cut out for you. Is this really your
> train of thought on this coil?
>
> BTW, 9 to 12 turn primary? No. This is only a "common" value we tend to end
> up at. Some coilers use over 20 turns and a few only use 2 or 1. What is
> meant I think is that higher turns adds impedance which helps attenuate the
> voltage on the primary for less problems and may even help with quenching.
> But no one is saying this as though it is wrong to use less than 9 turns.
> Simply that "some impedance" has been noted to help with gap quenching.
>
> ALSO, coupling you mentioned. No, coupling is fully adjustable. It's just
> that you "can" make a coils coupling to whatever you want and still have it
> even with the bottom secondary winding. For example. Suppose a coil builder
> is use to building a set distance from primary to secondary. And if the
> primary is even with the base, he usually ends up about 0.13 k on the
> coupling for the same coil size. Now say he lowers the primary to reduce the
> coupling and ends up at 0.11 which he finds best. Well, the primary itself
> could be redesigned so that when the primary is even with the sec base, he
> ends up at his found 0.11 ideal value. Thus, he ends up not needing to
> adjust the coupling. That's all there is to it. But adjusting the primary
> height is also perfectly acceptable and usual (since coilers don't seem to
> know what works best for a particular coil geometry).
>
> Best regards,
> Bart
>
>
>
> Grant Visser wrote:
>
>> Hi there,
>>
>> Suffering from sleep deprivation or 18 hour research / calc / sim /
>> research .... info overload at the moment, or BOTH! lol
>>
>> With my limited budget I am on a mission to get a solid base design
>> into my head before I begin throwing things together as I did last
>> time! *grin*
>>
>> The problem is that I have now done so much reading of content from so
>> many different viewpoints (over the years) that I have confused myself
>> COMPLETELY! Thus, I humbly beg your assistance ... or at least just a
>> darn good kick in the right direction!
>>
>> I have in front of me 26.06" of 3.543" Plexiglass tubing with 3mm
>> (0.1181") wall thickness (and don't want to waste a single mm of it!)
>> lol
>> Assuming 220V 50Hz mains and 2x 9KV/40mA NST's to power my new
>> coil(/s) (could add another 2 very soon!!!)
>> 3Kg of Double insulated magnet wire about to be ordered, ex works in
>> either 0.335mm (0.013188"), 0.355mm (0.013976"), 0.375mm (0.014763"),
>> or 0.4mm (0.015748") OD
>> Have tried my best but am not going to be able to afford the (less
>> than ideal) caps for a solid MMC so have decided that I will build a
>> quality bank of vertical plate caps for this coil. They'll never go to
>> waste!
>> I have also decided (I think) to go for a balanced split cap tank design.
>> Until I can find a decent blower I'll be using my current suction
>> quenched adjustable 2 gap design.
>> 1/4" copper tubing for the flat pancake primary coil
>> Oh, and yes I do now have a SOLID and dedicated RF Ground.
>> I do also have 3phase at my disposal .......
>>
>> Although it didn't even cross my mind initially, one of my biggest
>> stumbling blocks at this point is at what frequency I am going to run
>> this coil. This quandry started when I read a few posts from awhile
>> back regarding the primary winding and that it should have no less
>> than 12 to 15 turns and tuned at no less than 9 turns, and ensuring
>> that the final diameter or the primary is the same or close to the
>> winding height of the secondary! Apart from the fact that it actually
>> made sense to me from a coupling point of view, it also meant that I'd
>> be able to use a smaller main cap, so I was very happy right up until
>> I started doing the math / sims and it meant that I was going to have
>> to use a "SMALLER THAN RESONATE" capacitor which, seems to be an
>> absolute no no if I have understood the numerous other posts and
>> articles I have been reading!
>>
>> A further brainmangler that has crept in now is the other concept that
>> I had forgotten about ..... and that is that I would want to design my
>> secondary to have the length of wire I need to resonate with my
>> primary at a 1/4 wave! ie. At 220KHz the 1/4 wave is at 1118.1818ft
>> and I should thus use exactly that length of wire to coil my
>> secondary. Again this all makes perfect sense ....... right up until I
>> start doing the math and the sims ....... at which point, depending on
>> which program I use to model my coil, either the program yells insults
>> at me, or I simply cannot find a workable solution which allows me to
>> use all of the data above AND have a resonate coil with a decent hd
>> ratio! Going much below 220KHz means that I would have to increase the
>> length of my coiling wire to seemingly crazy HD ratio's!
>>
>> Now I do absolutely want to achieve the longest possible sparks from
>> this coil and I would like it to be an unstressed system allowing long
>> run times. I would also however like to use this coil to begin
>> demonstrating and researching the concepts of powering up light bulbs
>> etc from the ground waves for which I am going to have to construct a
>> top load with no breakout! With this in mind I was hoping to either
>> split the 26" form in half allowing me to coil two seperate identical
>> secondaries and use the second in a magnifier configuration. OR .... I
>> was even considering (but had not yet begun much research) using the
>> form for a BIPOLAR coil!
>>
>> I do realise that 3.5" is not exactly a MEGA COIL but it did seem to
>> me that it could be a nice little testbed to get me started with some
>> of the more interesting experiments! ???
>>
>> SO! Thats where I stand at this point! More confused than ever and
>> really hoping that you will be able to help me back onto the straight
>> and SPARKY!
>>
>> Grant Visser
>> Randburg, South Africa
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxxxxxx
>> http://www.pupman.com/mailman/listinfo/tesla
>>
>> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla