Re: lifter power supply (fwd)

[Steven Roys <sroys@xxxxxxxx>]

---------- Forwarded message ----------
Date: Mon, 28 Jul 2003 17:04:39 -0700
From: Jonathan Peakall <jpeakall@xxxxxxxxxxxx>
To: High Voltage list <hvlist@xxxxxxxxxx>
Subject: Re: lifter power supply (fwd)

Scott,

I have 4 "Tesla" brand diodes about 8 inches long. The are supposed to be
rated for 155kV at 23mA. I can't get any real specs on these, but they have
worked well on many xfrmrs up to 60kV or so. I got them from Jim Heagy, on
the TC list. Really handy to have kicking around.

Jonathan

www.madlabs.info

----- Original Message -----
From: "High Voltage list" <hvlist@xxxxxxxxxx>
To: <hvlist@xxxxxxxxxx>
Sent: Monday, July 28, 2003 2:14 PM
Subject: Re: lifter power supply (fwd)


> Original poster: Steven Roys <sroys@xxxxxxxx>
>
>
>
> ---------- Forwarded message ----------
> Date: Thu, 24 Jul 2003 22:58:29 -0700
> From: Scott Hanson <huil888@xxxxxxxxxxxx>
> To: High Voltage list <hvlist@xxxxxxxxxx>
> Subject: Re: lifter power supply (fwd)
>
> Jonathon -
>
> What type of rectifier set-up did you use with the 15/60 NST? How many of
> what type of diode, etc?
>
> Regards,
> Scott Hanson
>
>
> ----- Original Message -----
> From: "High Voltage list" <hvlist@xxxxxxxxxx>
> To: <hvlist@xxxxxxxxxx>
> Sent: Thursday, July 24, 2003 2:54 PM
> Subject: Re: lifter power supply (fwd)
>
>
> > Original poster: Steven Roys <sroys@xxxxxxxx>
> >
> >
> >
> > ---------- Forwarded message ----------
> > Date: Thu, 24 Jul 2003 08:33:17 -0700
> > From: Jonathan Peakall <jpeakall@xxxxxxxxxxxx>
> > To: High Voltage list <hvlist@xxxxxxxxxx>
> > Subject: Re: lifter power supply (fwd)
> >
> > Lance,
> >
> > I tried a 15kV, 60mA NST, and it isn't work. On the other hand, my house
> was
> > very damp, like where no static experiments work. I did get it to work
> with
> > a flyback setup, but erratically. I think the moisture and configuration
> of
> > my lifter was to blame. Interestingly, it wasn't my lightest lifter that
> > flew the best.
> >
> > Jonathan
> >
> > www.madlabs.info
> >
> > ----- Original Message -----
> > From: "High Voltage list" <hvlist@xxxxxxxxxx>
> > To: <hvlist@xxxxxxxxxx>
> > Sent: Thursday, July 24, 2003 7:41 AM
> > Subject: lifter power supply (fwd)
> >
> >
> > > Original poster: Steven Roys <sroys@xxxxxxxx>
> > >
> > >
> > >
> > > ---------- Forwarded message ----------
> > > Date: Thu, 24 Jul 2003 01:19:54 -0700
> > > From: harry <harry@xxxxxxxx>
> > > To: hvlist@xxxxxxxxxx
> > > Subject: lifter power supply
> > >
> > > Hello
> > >
> > > I have been toying with the idea of building a lifter and was
wondering
> if
> > a 15,000V 30Ma NST would make an acceptable power supply ?
> > >
> > > Lance
> > >
> > >
> > >
> >
> >
> > ---
> > [This E-mail scanned for viruses by Surfside Internet]
> >
> >
>
> ---
> [This E-mail scanned for viruses by Surfside Internet]
>
>
>