[Prev][Next][Index][Thread]

Web page update




----------
From:  D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
Sent:  Wednesday, March 11, 1998 1:28 PM
To:  Tesla List
Subject:  Re: Web page update

to: Bill

Thanks for the update Bill -- I also noted Mark R's posting on this matter.
 Good luck with your work on this project.

DR.RESONANCE-at-next-wave-dot-net

----------
> From: Tesla List <tesla-at-pupman-dot-com>
> To: 'Tesla List' <tesla-at-pupman-dot-com>
> Subject: Web page update
> Date: Tuesday, March 10, 1998 9:56 PM
> 
> 
> ----------
> From:  Wysock, William C. [SMTP:Wysock-at-courier8.aero-dot-org]
> Sent:  Tuesday, March 10, 1998 7:47 AM
> To:  Tesla List
> Cc:  ttr
> Subject:  RE: Web page update
> 
> 
> To D.C.,
> 
> The primary of the Master Oscillator is made of two single,
> parallel connected turns, wound around the circumference
> of the outer-most helical layer of secondary turns (this is
> the layer that contains 15 turns at a 20 foot diameter, and is
> 30 inches high.  The primary conductors are 750 MCM
> welding cable, as are the inter-connect cables between
> the tank capacitor bank and rotary gap.  These are also
> double conductors.  The ground connection is to the lower
> most secondary coil turn at the outside layer.   The secondary
> will be made from fine stranded, PVC insulated #2 AWG cable.
> I had not made this clear in that illustration.
> Thank you for the question.
> 
> Bill Wysock.
>  ----------
> From: Tesla List
> To: Tesla List
> Subject: Web page update
> Date: Monday, March 09, 1998 9:44PM
> 
> 
>  ----------
> From:  D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
> Sent:  Monday, March 09, 1998 6:56 PM
> To:  Tesla List
> Subject:  Re: Web page update
> 
> to: Bill
> 
> Sounds like a neat project.  Are you applying the traditional HV from the
> xmfr-cap-RSG between the outermost turn and a tap on a more innermost
> turn??  Did you plan on using perhaps 20-60 turns of copper tubing or
using
> some type of welding cable for your pri-sec driver coil?
> 
> DR.RESONANCE-at-next-wave-dot-net
> 
> 
> 
> > From:  Wysock, William C. [SMTP:Wysock-at-courier8.aero-dot-org]
> > Sent:  Monday, March 09, 1998 10:51 AM
> 
> > For many months now, the references to the "13M Story"
> > have not had images (figures 1 thru 19) at the end of the
> > article, on my web site.    They are posted now.
> <snip>
> > The outer-most winding of the
> > secondary is connected to ground, and the center-most winding
> > turn, is the high voltage output of this system, which drives into
> > the extra coil.
> >
> > This system is at present, under preliminary construction.  It
> > encompasses the attributes of Tesla's early designs, as well as
> > what is [speculated] Tesla accomplished in his final design at
> > Wardenclyffe.
> <snip>
> > Before a full-scale Model 14M is built, I plan to construct a 1/10
> > scale model, to prove my hypothisis of design.  I will share the
> > results of these investigations here, on the Tesla List.
> >
> > Bill Wysock.
> > ___________________________
> > Tesla Technology Research
> 
>