[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Wiring MOTs



Original poster: "Aaron Aab" <striker754-at-earthlink-dot-net> 

Well I got four of them connected.

Connected all the neutrals together, put 2 transformers on each 110 phase of
the 220.

Took the 2 inside transformers with the secondary connected to the core, and
connected the other leg to the next transformers secondary.

Cores werent grounded to anything.

With the HV leads unshorted, one input leg drew 12A and the other drew 8A,
shorted one drew 40A and the other one still drew 8A?????

How can I figure out the output volts/amps?

Aaron

----- Original Message -----
From: "Tesla list" <tesla-at-pupman-dot-com>
To: <tesla-at-pupman-dot-com>
Sent: Saturday, January 24, 2004 7:15 PM
Subject: Re: Wiring MOTs


 > Original poster: "Hydrogen18" <hydrogen18-at-hydrogen18-dot-com>
 >
 > Ok, I'm no genius on electronics but know a good bit. Heres how I would do
 > it. Ground the first core. Take the high voltage output wire of that one,
 > connect it to the core of the next. Then take the high voltage wire coming
 > out of that one and connect it to the core of the next. The ground core
will
 > be your 0 volts, the final high voltage wire will be your high voltage
out.
 >
 > ----- Original Message -----
 > From: "Tesla list" <tesla-at-pupman-dot-com>
 > To: <tesla-at-pupman-dot-com>
 > Sent: Saturday, January 24, 2004 4:54 PM
 > Subject: Re: Wiring MOTs
 >
 >
 >  > Original poster: "Aaron Aab" <striker754-at-earthlink-dot-net>
 >  >
 >  > So ground the cores or no? I've seen people with 2 MOTs ground them,
but i
 >  > suppose 4 is different since you have the secondarys connected
 >  >
 >  >
 >  > ----- Original Message -----
 >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  > To: <tesla-at-pupman-dot-com>
 >  > Sent: Saturday, January 24, 2004 2:30 PM
 >  > Subject: Re: Wiring MOTs
 >  >
 >  >
 >  >  > Original poster: "Hydrogen18" <hydrogen18-at-hydrogen18-dot-com>
 >  >  >
 >  >  > Is it just me, or if he wants them in series, he could not ground
all
 > of
 >  > the
 >  >  > cores?
 >  >  > ----- Original Message -----
 >  >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  >  > To: <tesla-at-pupman-dot-com>
 >  >  > Sent: Saturday, January 24, 2004 12:46 AM
 >  >  > Subject: Re: Wiring MOTs
 >  >  >
 >  >  >
 >  >  >  > Original poster: tesla <tesla-at-paradise-dot-net.nz>
 >  >  >  >
 >  >  >  > Hi Aaron
 >  >  >  >
 >  >  >  > I would predict you will get conflicting answers to the question.
 >  >  >  > I ground my cores on ALL MOT's as I want a ground barrier between
 > the
 >  >  >  > secondary and the mains side. Some advocate floating the core to
 >  >  > distribute
 >  >  >  > the voltage stresses.
 >  >  >  >
 >  >  >  > If the MOT is in good oil the stress issue does not seem to be a
 >  > problem
 >  >  >  > based on postings and my own experience.
 >  >  >  >
 >  >  >  > If I get a secondary RF strike I do not want that getting to the
 > mains
 >  >  >  > windings.
 >  >  >  > Good luck, MOT's are taking over I think
 >  >  >  > Ted L in NZ
 >  >  >  >
 >  >  >  > ----- Original Message -----
 >  >  >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  >  >  > To: <tesla-at-pupman-dot-com>
 >  >  >  > Sent: Saturday, January 24, 2004 1:44 PM
 >  >  >  > Subject: Wiring MOTs
 >  >  >  >
 >  >  >  >
 >  >  >  >  > Original poster: "Aaron Aab" <striker754-at-earthlink-dot-net>
 >  >  >  >  >
 >  >  >  >  > Im putting 4 MOTs in series with the center 2 secondaries one
 >  > connected
 >  >  > to
 >  >  >  >  > ground.
 >  >  >  >  >
 >  >  >  >  > Do I connect all the cores to ground?
 >  >  >  >  >
 >  >  >  >  > Also, how do i wire up a MOT to use as a ballast?
 >  >  >  >  >
 >  >  >  >  > Aaron
 >  >  >  >  >
 >  >  >  >  >
 >  >  >  >
 >  >  >
 >  >  >
 >  >
 >  >
 >  >
 >
 >
 > ---
 > Outgoing mail is certified Virus Free.
 > Checked by AVG anti-virus system (http://www.grisoft-dot-com).
 > Version: 6.0.556 / Virus Database: 348 - Release Date: 12/27/2003
 >
 >