Re: Wiring suggestions

["Tesla list" <tesla-at-pupman-dot-com>]

Original poster: "Dr. Resonance" <resonance-at-jvlnet-dot-com> 


We use the 300 Volt cable and it does not fail unless pushed over-current
for long periods of time.

You should be safe.

Dr. Resonance


----- >
 > I bought some 10/3 300 volt stuff today. I asked for 10/3 600 volt but he
 > sold me the wrong stuff I realized after I got out of the store. If it
fails
 > I'll just tell them I asked for 600 volt and they sold me 300 so its there
 > fault. Thanks for the help guys.
 >
 > ---Eric
 > ----- Original Message -----
 > From: "Tesla list" <tesla-at-pupman-dot-com>
 > To: <tesla-at-pupman-dot-com>
 > Sent: Sunday, May 23, 2004 4:08 PM
 > Subject: Re: Wiring suggestions
 >
 >
 >  > Original poster: "Jim Lux" <jimlux-at-earthlink-dot-net>
 >  >
 >  > If you're using 240V, then why not use a grounding plug with the two
hots
 >  > and ground?  You can make 120 from 240V inside your box if you need it
 > with
 >  > a small transformer or other means.
 >  >
 >  > Anytime someone talks about creating a piece of high power electrical
 > gear,
 >  > and doesn't connect a "safety ground" at the same time, I get a bit
 > nervous.
 >  > (aside from it being pretty blatantly "not to code"... the only cases I
 > can
 >  > recall where you don't need an explicit ground connection, tied to the
 > power
 >  > ground in some fairly reliable way, is with permanently installed
 > appliances
 >  > where the grounding is assured by "other means").
 >  >
 >  > Yes, they DO sell plugs that have three blades and no ground, but
they're
 >  > for special purposes, and their use is deprecated on new equipment.
 >  >
 >  > The ground stake may be fine for RF (although maybe not...), it's not
 >  > sufficient for electrical safety purposes, unless you've separately run
a
 >  > wire to the electrical system grounding point and bonded it
sufficiently
 >  > you're taking your life (or someone else's) life in your hands. (that
 >  > doesn't mean a 24AWG cliplead, but is a "exothermically welded" or
 > "approved
 >  > pressure connector" sort of thing)
 >  >
 >  > The correct plugs and receptacles are too cheap to fool with trying to
 >  > cobble together something else.  If you're running enough power that
you
 >  > need 30Amp service (i.e. you're not just running a single NST, etc.)
then
 >  > you need to make the $20-40 investment in the right plug and
receptacle.
 >  > That AWG 10 power cord is going to set you back that much if it's very
 > long.
 >  >
 >  >
 >  > ----- Original Message -----
 >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  > To: <tesla-at-pupman-dot-com>
 >  > Sent: Sunday, May 23, 2004 10:25 AM
 >  > Subject: Re: Wiring suggestions
 >  >
 >  >
 >  >  > Original poster: "Hydrogen18" <hydrogen18-at-hydrogen18-dot-com>
 >  >  >
 >  >  > The plug I use has both sides of the line and the neutral, no
ground.
 > My
 >  >  > garage wasnt wired for 4 wire. Plus, I have a ground stake which
will
 > be
 >  >  > connected to this thing when in use. I'm probaly goign to get 3 wire
10
 >  >  > guage tommorow.
 >  >  >
 >  >  > ---Eric
 >  >  > ----- Original Message -----
 >  >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  >  > To: <tesla-at-pupman-dot-com>
 >  >  > Sent: Saturday, May 22, 2004 7:34 PM
 >  >  > Subject: Re: Wiring suggestions
 >  >  >
 >  >  >
 >  >  >  > Original poster: "Jim Lux" <jimlux-at-earthlink-dot-net>
 >  >  >  >
 >  >  >  >
 >  >  >  > ----- Original Message -----
 >  >  >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  >  >  > To: <tesla-at-pupman-dot-com>
 >  >  >  > Sent: Saturday, May 22, 2004 3:41 PM
 >  >  >  > Subject: Re: Wiring suggestions
 >  >  >  >
 >  >  >  >
 >  >  >  >  > Original poster: "Harold Weiss" <hweiss-at-new.rr-dot-com>
 >  >  >  >  >
 >  >  >  >  > Hi Eric,
 >  >  >  >  >
 >  >  >  >  > You would want at least 10 gauge wire for 30A.  10/4 SOW cable
 > can
 >  > be
 >  >  >  > bought
 >  >  >  >  > at most home improvement stores.  The black and red are your
hot
 >  > leads,
 >  >  >  > with
 >  >  >  >  > the white being neutral and the green ground.  Preferably go
with
 >  > 30A
 >  >  >  > twist
 >  >  >  >  > lock connections, as the 30A dryer plugs aren't the safest
things
 > to
 >  >  >  > unplug
 >  >  >  >  > if the line is hot. (too easy to get fingers into the prongs)
 >  >  >  >  >
 >  >  >  >  >
 >  >
 >  >
 >  >
 >
 >
 >