Re: Jim mitchell's solid state tesla coil board

["Tesla list" <tesla-at-pupman-dot-com>]

Original poster: Kreso Bukvic <kreso.bukvic-at-kc.htnet.hr> 

Are these boards still available?

Do you have a picture of the board?

Best Regards

Kreso Bukvic
----- Original Message -----
From: "Tesla list" <tesla-at-pupman-dot-com>
To: <tesla-at-pupman-dot-com>
Sent: Tuesday, May 18, 2004 2:54 AM
Subject: Re: Jim mitchell's solid state tesla coil board


 > Original poster: "Jim Mitchell" <Electrontube-at-sbcglobal-dot-net>
 >
 > All,
 >
 > I have written intructions.  It is posible that some of you have not
gotten
 > them or something.  IF so, the instructions for my board are here.
 >
http://www.hot-streamer-dot-com/electrontube/temp/Self%20Resonant%20SSTC%20board
%20DR.doc
 > If you need further help, you may email em privately.  Please note,  when
 > you bought the board,  I explained fully that this was just the driver.  I
 > can't give everyone step by step instructions via email if you don't
bother
 > to read the ones I've written already!
 >
 > Regards - Jim Mitchell
 > ----- Original Message -----
 > From: "Tesla list" <tesla-at-pupman-dot-com>
 > To: <tesla-at-pupman-dot-com>
 > Sent: Monday, May 17, 2004 2:07 PM
 > Subject: RE: Jim mitchell's solid state tesla coil board
 >
 >
 >  > Original poster: "Daniel Kline" <daniel_kline-at-med.unc.edu>
 >  >
 >  >
 >  >
 >  >  > -----Original Message-----
 >  >  > From: Tesla list [mailto:tesla-at-pupman-dot-com]
 >  >  > Sent: Monday, May 17, 2004 10:21 AM
 >  >  > To: tesla-at-pupman-dot-com
 >  >  > Subject: Jim mitchell's solid state tesla coil board
 >  >  >
 >  >  >
 >  >  > Original poster: "Arpit Thomas" <arpit-at-inzo-dot-org>
 >  >  >
 >  >  >
 >  >  >
 >  >  > Hi, I got Jim's sstc board today, and was wondering whether
 >  >  > anyone has
 >  >  > assembled it yet. I don't really understand how it all works,
 >  >  > This will be
 >  >  > my first attempt at a sstc.Has anyone got it working
 >  >  > successfully? what
 >  >  > What is the purpose of the 2 big variable resistors? IT seems
 >  >  > to me that
 >  >  > one of them is connected right across the supply, so if was
 >  >  > using an 80 amp
 >  >  > 5 volt supply and st the pot to minim resistance itd be
 >  >  > impressive to say
 >  >  > the least. ANy tips would be much appreciated.
 >  >  >
 >  >  > thanks,
 >  >  > Arpit THomas
 >  >
 >  > Hi Arpit,
 >  > I'm with you in this. I got a board too, but I'm not up-to-speed on
 >  > SSTCs either.
 >  > I've asked a couple of people offline about how to set one up, but what
 >  > I really need
 >  > is a step-by-step instruction manual for setting up the board, the
 >  > H-bridge and the coil.
 >  > I got answers like "Just build an H-bridge and attach it to the board
 >  > and then run your coil."
 >  > That's like me saying "Just get a couple of chop-sticks, a hair-tie, an
 >  > expanding
 >  > lens and a box of sand. Shine your laser through the lens and onto your
 >  > holography film,
 >  > and you've got a hologram!"
 >  > If anyone has detailed instructions, please let us know :)
 >  > Thanks,
 >  > Dan K.
 >  >
 >  >
 >
 >
 >
 >