[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Resonance



Original poster: "Steven Steele" <sbsteele@xxxxxxxxxxxxx>

I insulated each layer with a whole lot of nail polish.
Would that be OK?

       Steven Steele
----- Original Message ----- From: "Tesla list" <tesla@xxxxxxxxxx>
To: <tesla@xxxxxxxxxx>
Sent: Thursday, April 07, 2005 10:48 AM
Subject: Re: Resonance


Original poster: "Mike" <mike.marcum@xxxxxxxxxxxx>

99% of the time more than 1 layer is bad unless you go to extreme measures to insulate it (.125" thick layer of kapton film between layers/potting in SF6 or oil/etc) which most of the time just much cheaper to use a bigger coil form with 1 layer. As is I'm willing to bet that your coil will short itself out and maybe catch fire if the input power is decent.

Mike
----- Original Message ----- From: "Tesla list" <tesla@xxxxxxxxxx>
To: <tesla@xxxxxxxxxx>
Sent: Wednesday, April 06, 2005 11:58 PM
Subject: Re: Resonance


Original poster: "Steven Steele" <sbsteele@xxxxxxxxxxxxx>

Not yet, I, still waiting on the caps.
Why, is this a bad thing? (8^0)
Now I'm worried.
Should I be?
                                       Steven Steele

----- Original Message ----- From: "Tesla list" <tesla@xxxxxxxxxx>
To: <tesla@xxxxxxxxxx>
Sent: Wednesday, April 06, 2005 7:58 PM
Subject: Re: Resonance


Original poster: "Paul B. Brodie" <pbbrodie@xxxxxxxxxxxxx>

Steven,
Am I understanding you correctly that you have wound more than one layer of wire on your secondary coil?? Have you run this coil successfully yet?
Paul Brodie
----- Original Message -----
From: "Tesla list" <<mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
To: <<mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
Sent: Wednesday, April 06, 2005 2:21 PM
Subject: Re: Resonance


> Original poster: "Steven Steele"
<<mailto:sbsteele@xxxxxxxxxxxxx>sbsteele@xxxxxxxxxxxxx>
>
> I was going to do that, but it's hard to count because I'm using 36 > AWG
> wire. It would be like counting hairs on somebody's head. Plus, the >
windngs
> on the outer layer aren't very close becaus by that time I was
running > out
> of wire. Also I don't rememer how many layers I had. :(
> Oh well. Thanks anyway. If I knew how much wire I used I could also
> calculate it, but I don't. :(
>
> Steven Steele
> ----- Original Message ----- From: "Tesla list"
<<mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
> To: <<mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
> Sent: Wednesday, April 06, 2005 10:09 AM
> Subject: Re: Resonance
>
>
>>Original poster: "Gerald  Reynolds"
<<mailto:gerryreynolds@xxxxxxxxxxxxx>gerryreynolds@xxxxxxxxxxxxx>
>>
>>Hi Steven,
>>
>>Asuming your secondary is closed wound, count the turns per inch and
>>multiply by the winding length.  That'll get you close.
>>
>>Gerry R.
>>
>>>Original poster: "Steven Steele"
<<mailto:sbsteele@xxxxxxxxxxxxx>sbsteele@xxxxxxxxxxxxx>
>>>
>>>That woul be great...
>>>Except for the fact that I didn't count the number of windings in the
>>>secondary and i'm not entirely sure how much wire I used. I know
that >>>it
>>>was less than 1,000' because I bought  a 1,000' roll. But I used
some >>>of
>>>it to test the winder( I don't know how much) and I ended up
with >>>extra.
>>>I don't even know how many times I wound it up and down! :(
>>>    I'll check it out though. Thanks.
>>
>>
>>
>>
>
>
>
>