[Home][2015 Index] Re: [TCML] Mid sized Tesla Coil - Done [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] Mid sized Tesla Coil - Done



If you have a hobby lobby in your area they sell an assortment of pie pans in different sizes.

John Cooper


Sent from my Samsung GALAXY S5™, a Cricket 4G LTE smartphone


-------- Original message --------
From: Timothy Gilmore <tdg8934@xxxxxxxxx> 
Date:03/22/2015  16:02  (GMT-06:00) 
To: Tesla Coil Mailing List <tesla@xxxxxxxxxx> 
Cc:  
Subject: Re: [TCML] Mid sized Tesla Coil - Done 

Thanks Jon!

I've been putting many hours in every day trying to get it ready for the
showing next Friday. When you say make the toroid topload bigger, I'm
assuming you mean use larger ducting like 8" or larger if I can find it
(instead of the 6" I have now). It was hard to find the right size middle
section and was lucky to find 13" foil pizza trays (as the 4" ducting
torroid toploads use more easily found 9" pie tins). I also used foil
wrapped cardboard inside for more strength but it wants to shift around too
much unless kept tight. Is it more important to have a larger middle
section to the torroid topload or the ducting size (i.e. 6", 8", 12")? It
might be easier to locate a more ridged larger middle section and wrap the
6"+ ducting around that,

Also wrapping it all in aluminum tape would keep it more uniform and flat
(less crinkle like), I also found that adding a large spike nail to the top
of the torroid middle section (wedge in) would direct more sparks out the
end of it. So making it more uniform (or bigger) will allow for less medium
sized sparks and will discharge sparks that are thicker and longer?


Tim

On Sun, Mar 22, 2015 at 1:40 PM, Jon Danniken <danniken@xxxxxxxxxxx> wrote:

> Wow that looks great, you got that together fast!
>
> A couple suggestions would be to work on your topload to eliminate the
> multiple streamers (assuming you don't like multiple streamers), so that
> you end up with one larger streamer.   Part of the issue can be caused
> by the lack of a uniform surface across the topload, providing multiple
> breakout points, or the cause could be too small of a topload.  You
> could try cleaning up the topload you have to see if things improve, and
> if not, build a larger topload, taking care to keep it uniform (aluminum
> tape can come in handy for the seams).
>
> When you get the topload sorted out, you can work on coupling, by
> raising the primary (or lowering the secondary), gradually, until you
> start getting racing sparks.  When that happens, back it off a bit and
> you will be as tight as you can be.
>
> Again, good job on this one!
>
> Jon
>
>
> On 03/22/2015 09:04 AM, Timothy Gilmore wrote:
> > Here is a better link showing both videos. Another one tonight also.
> >
> > https://www.youtube.com/channel/UCagcW23FY4yx6D4kWodMbKA
> >
> > Tim
> >
> > On Sun, Mar 22, 2015 at 10:36 AM, Timothy Gilmore <tdg8934@xxxxxxxxx>
> wrote:
> >
> >> I finally finished my long awaited mid sized tesla coil. The Tesla Map
> >> software was spot on in the tuning of taping it between turn 12 and 13.
> >> Most sparks are over 3 feet and many are over 4 feet long. I have 2
> NSTs at
> >> 15kv 60mA using capacitor equivalent of 30nF 30kv stacked in triple
> layer.
> >> It uses 2 parallel tungsten spark gaps quenched by a squirrel cage fan.
> The
> >> primary is taped at 12.5 turns on the 1/4" copper tubing starting at 8"
> >> outwards. The secondary is 31" tall by 6" diameter of 26 awg wire of
> 1400
> >> turns. I'm having about 10 of my friends and co-workers over next Friday
> >> for an outdoor showing and cookout after work.
> >>
> >> Check out the 2 dry run videos. One I was holding a florescent light
> bulb
> >> and the lightning jumped over to it and I got zapped through the glass
> >> part. Ouch. Ok but getting the long florescent tubes today. Over $1200
> to
> >> make it.
> >>
> >> https://www.youtube.com/watch?v=RtWGQDUqzm4
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla