[Home][2015 Index] Re: [TCML] drsstc bus capacitors [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] drsstc bus capacitors



The design is not complete yet.  My budget is such that I'm designing to fit components as I obtain them rather than obtaining the components to fit a set design.  Currently I have:
- five CM600HA-24H IGBTs (good to have a spare right?) for a full bridge topology.- 1600V  200A  3phase bridge rectifier (planning to use just 1 of the 3 pairs of diodes though I might as well parallel them)- eight 3300V, 4500VDC peak, 6uF polypropylene GTO caps rated at 7200A peak current (should make for a pretty beefy tank cap between 0.75 and 3.0!! uF depending on how I series/parallel these).  That should allow me to go for either a high or low impedance design.- 20+ of the previously mentioned electrolytic capacitors (awaiting response from the list to see if I can try these before looking for something else)- two 1156 powerstat variacs (I expect I should be good for up to 15KVA or so -> maybe 10kW real power).

As of now the plan is to use the variacs to feed a voltage doubler for up to 680V at the bus.  I have designed what should be a minimal inductance bus for the bridge/lytic cap connections using aluminum angle extrusion.  I figure I'll wind a 48" to 60" secondary on 12" nominal PVC unless I come across a good deal on something else to use as a form.  I haven't yet determined what size wire.  A 10 lb spool of 24 AWG or 11 lb spool of 23 AWG should be good for 2000-2400 turns.  With a 12"x48" ish toroid that should keep my natural freq. low.  Shooting for around 30-35kHz loaded.  I still haven't thought through all the implications/differences of choosing to use a high capacitance MMC with low turn primary vs a smaller MMC (physically larger since it will use more of my caps in series) and long primary.  I will probably be seeking some advice here when the time comes.  I haven't picked a gate drive design yet, but I'm leaning toward a GTD approach.  
Thomas

      From: "msweeney23@xxxxxxxxx" <msweeney23@xxxxxxxxx>
 To: Tesla Coil Mailing List <tesla@xxxxxxxxxx> 
 Sent: Thursday, October 8, 2015 11:49 AM
 Subject: Re: [TCML] drsstc bus capacitors
   
I cant say anything on the caps but would be interested in what design you are using, if its possible to share?

Regards,

Matt

----- Reply message -----
From: "Thomas Shurtz via Tesla" <tesla@xxxxxxxxxx>
To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
Subject: [TCML] drsstc bus capacitors
Date: Thu, Oct 8, 2015 11:21 AM

I have a bunch of Hitachi electrolytic capacitors that came out of some old discarded industrial equipment (I believe it was a VFD for an elevator) They are HCGF3A series, and I can't find datasheets on them.  They are 450v 5600uF caps and I have a good 2 dozen of them.  I was thinking of using them for a CM600 based DRSSTC.  On the one hand I feel like the lytic specs aren't all that important, and the datasheets on the hgcf5a and f6a series caps (which might be the newer versions of what I've got?) look like they would be suitable for this use, but the screw terminals on my caps look kinda small (about 1 cm diameter) for the cap size (about 10cm diameter) which hints that they might not be the right thing for the job.  What do I stand to lose if I try these out and they aren't up to the right specs?  I mean they are free so I'm not out anything if I blow the juice out the vent hole on a few of them, but what other problems might I see?  What failures have people seen that 
 they blame on poor bus/doubler electrolytics?
Thomas
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla


  
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla