[Home][2019 Index] Re: [TCML] Pole transformer repair [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] Pole transformer repair



Tyler, 

So sorry to here of the untimely death of your transformer. I destroyed a smaller 5 kVA unit doing pretty much the same thing that you described several years ago and more recently, I smoked a 3 kVA pt in the same manner. I am surprised that your 25 kVA beast fell prey to the same fate, though, as I have been using my 25 kVA rated piggy for the same purpose (of pulling huge, wicked power arcs by running the pig’s output through a 0.48 uFd rated pulse cap and drawing an arc, taking advantage of the near series resonant condition of the pig’s hv winding L with the capacitor’s C!) 

Since you stated that your employer seldom scraps any of their transformers, are you certain that it wasn’t already internally damaged, hence them letting you have it? 

Good luck,
David

Sent from my iPhone

> On Jan 3, 2019, at 7:37 AM, Tyler LaVite <tlavite@xxxxxxxxx> wrote:
> 
> Scott you don’t have a good link for a source for the paper you used and the wire do you? I’ll know more once I drain my tank and pull the core out this Friday after work. I work for a local power company but it’s hard to get transformers from them since they don’t trash any of them lol.
> 
> Sent from my iPhone
> 
>> On Jan 2, 2019, at 9:30 PM, Scott Kraus via Tesla <tesla@xxxxxxxxxx> wrote:
>> 
>> The one I repaired had all copper windings. The windings were set up so half the low voltage winding was on the outside then a 7200 volt winding. Next was another 7200 volt winding. Then finally the inside was the other half of the low voltage winding. The core had two sides of laminations wrapped through it. Each one was smaller than the one before it so I had to lay them out in order so they could be put back the same way. One of the 7200 volt windings was shot so I pulled the wire out from the side until all the windings could be separated. I rewound the damaged one and wrapped each layer in nomex paper. Probably better than it was. I went too far with the number of turns. Came out with 16.5 kV when I tested it. I think it was about 4 volts per turn. I ran my medium size  coil with it and it held up fine. I have a few videos of it running at D.C.s show in Baraboo Wi. back about 2010 on my Facebook page if interested.
>> Scott
>>   On Wednesday, January 2, 2019, 8:14:15 PM CST, David Buchanan <thebuchanan@xxxxxxxx> wrote:  
>> 
>> Probably wound with aluminum wire - difficult to splice or repair. I can advise on repair if no one else volunteers. 
>> 
>> Sent from my iPhone
>> 
>>> On Jan 2, 2019, at 5:49 PM, Tyler LaVite <tlavite@xxxxxxxxx> wrote:
>>> 
>>> Welp has anyone on here ever repaired a pole transformer? I was using a pulse capacitor on a Jacob’s ladder on a 25kva pole transformer when the arc stopped I shut everything down immediately hooked up just the Jacob’s ladder and nothing... it’s pulling 58 amps and not putting anything out. When it was at full arc with no capacitor it always pulled 80 amps... I popped the top and noticed a small amount of black haze in the oil. So obviously something burned up... gonna drain it this weekend and pull the core out hopefully it’s not anything insane I spent allot of money on this transformer and it was brand new never used. Guess that’s the name of the game though you blow crap up lol
>>> 
>>> Sent from my iPhone
>>> _______________________________________________
>>> Tesla mailing list
>>> Tesla@xxxxxxxxxxxxxxxxxx
>>> https://www.pupman.com/mailman/listinfo/tesla
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxxxxxxxxxx
>> https://www.pupman.com/mailman/listinfo/tesla
>> 
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxxxxxxxxxx
>> https://www.pupman.com/mailman/listinfo/tesla
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxxxxxx
> https://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxxxxxx
https://www.pupman.com/mailman/listinfo/tesla