[Home][2020 Index] Re: [TCML] "Modern" Spark Gap Designs? [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] "Modern" Spark Gap Designs?



Paint your PVC with acrylic-based latex paint. UV radiation cannot
penetrate the surface of latex paint.

On Thu, Jan 30, 2020 at 12:09 AM Steve White <steve.white1@xxxxxxxxx> wrote:

> I think you will run into a problem if you try to bridge more than two
> gaps. I built my SRSG to allow for either 2 gaps or 4 gaps. I initially
> tried it with 4 gaps and no matter how closely I spaced the electrodes, I
> got inconsistent firing. This is with a 14.4 KV pole transformer. I then
> switched to 2 gaps and got completely consistent firing at 240 BPS. I have
> used 2 gaps ever since. My SRSG runs very nicely with a 1/2 HP AC induction
> motor modified to be synchronous. This is with a 12 inch diameter G10 rotor
> 1/2 inch thick running at 3600 RPM.
>
> Steve White
> Cedar Rapids, Iowa
>
> ----- Original Message -----
> From: "Dan Kunkel" <dankunkel@xxxxxxxxx>
> To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
> Sent: Wednesday, January 29, 2020 6:25:19 PM
> Subject: Re: [TCML] "Modern" Spark Gap Designs?
>
> Tedd,
> A single static gap would not quench very well, at least without the aide
> of moving air, vacuum, magnets, etc. However, a MULTIPLE series gap does
> seem to perform quite well. Yes you loose a little power with each "hop",
> but in the end you gain due to faster quenching. Each break allows the
> power to be divided up and is easier to quench.
>
> A rotary gap is OK at quenching, but it only has two "hops" (as compared
> with a typical TCBOR or RQ style gap). Plus the speed of electricity is
> much faster than the mechanical dwell time of the electrodes in a rotary
> gap. So the rotational aspect of a rotary does not do anything for
> quenching. Plenty of folks have reported "following around" on a rotary gap
> due to lack of quenching (there are videos on youtube as well).
>
> ~Dan
> Kansas city area
>
> On Wed, Jan 29, 2020 at 5:32 PM Tedd Dillard <tedd.dillard@xxxxxxxxx>
> wrote:
>
> > Why would a static gap quince better than a rotatary gap?
> >
> > On Jan 29, 2020 5:14 PM, "Gary Lau" <glau1024@xxxxxxxxx> wrote:
> >
> > > I have no experience with gaps for anything larger than an NST power
> > supply
> > > so can't comment on the series quench configuration.  But based on my
> > > experience, I suspect the use of PVC in proximity to the gaps is a less
> > > than ideal idea.  Even using a single NST, the white PVC turns an
> > > unsightly brown color due to the intense UV emitted by the gap.  I
> don't
> > > know how its insulating or mechanical strength might be affected, but
> > > better to use G10 if available.
> > >
> > > Regards, Gary Lau
> > > MA, USA
> > >
> > > On Wed, Jan 29, 2020 at 1:03 PM Daniel Kunkel <dankunkel@xxxxxxxxx>
> > wrote:
> > >
> > > > Hello Tesla List!
> > > > I am starting to work on my next spark gap for a 6-10 KVA magnifier.
> It
> > > > seems the definitive spark gap design is that from Richard Hull/TCBOR
> > > using
> > > > a rotary gap (to control timing only) combined with a multiple break
> > > series
> > > > gap (to control quench only). Is there a better approach for gap
> design
> > > and
> > > > construction?
> > > >
> > > > Currently my plan is to use a 3.5 HP DC motor to spin a G10 disk with
> > > > tungsten electrodes and combine it with the PVC + copper tubes + fan
> > > series
> > > > gap.
> > > >
> > > > Thanks,
> > > > ~Dan
> > > > Kansas City area
> > > > _______________________________________________
> > > > Tesla mailing list
> > > > Tesla@xxxxxxxxxxxxxxxxxx
> > > > https://www.pupman.com/mailman/listinfo/tesla
> > > >
> > > _______________________________________________
> > > Tesla mailing list
> > > Tesla@xxxxxxxxxxxxxxxxxx
> > > https://www.pupman.com/mailman/listinfo/tesla
> > >
> > _______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxxxxxxxxxx
> > https://www.pupman.com/mailman/listinfo/tesla
> >
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxxxxxx
> https://www.pupman.com/mailman/listinfo/tesla
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxxxxxx
> https://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxxxxxx
https://www.pupman.com/mailman/listinfo/tesla