[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: synchronous gap help (fwd)



---------- Forwarded message ----------
Date: Tue, 10 Jul 2007 14:32:46 -0700 (GMT-07:00)
From: penny831@xxxxxxxxxxxxx
To: Tesla list <tesla@xxxxxxxxxx>
Subject: RE: synchronous gap help (fwd)

I've already built the propellor gap using the .125 and the entire device
is housed in a cabinet with an blower to keep it cooled. I'll run it and
see how it does because as you said, the 1/4" is really expensive.
Adapting to the larger rods would be simple, just a few minutes on the
drill press! Does anyone have the Geek Group capacitor chart that includes
the cap value using the SRSG? I have the one for the static gaps but it
doesn't include anything for the SRSG. As always, thanks again.

Tony

-----Original Message-----
>From: Tesla list <tesla@xxxxxxxxxx>
>Sent: Jul 10, 2007 1:02 PM
>To: tesla@xxxxxxxxxx
>Subject: RE: synchronous gap help (fwd)
>
>
>---------- Forwarded message ----------
>Date: Tue, 10 Jul 2007 15:49:45 -0400
>From: "Lau, Gary" <Gary.Lau@xxxxxx>
>To: Tesla list <tesla@xxxxxxxxxx>
>Subject: RE: synchronous gap help (fwd)
>
>Red-hot with just a 15/120 NST?  With my 15/60 NST and 5/32" tungsten
>rod, I can touch any part of the propeller-gap electrodes immediately
>following a 1-3 minute run.  The stationary electrodes do tend to get
>hotter due to less airflow, but definitely not approaching
>incandescence.  
>
>I don't mean to nit-pick, but 1/4" rod is a bit pricey and unnecessary,
>IMO.
>
>Regards, Gary Lau
>MA, USA
>
>> Date: Tue, 10 Jul 2007 14:04:49 -0500
>> From: resonance <resonance@xxxxxxxxxxxx>
>> To: Tesla list <tesla@xxxxxxxxxx>
>> Subject: Re: synchronous gap help (fwd)
>> 
>> 
>> 
>> At this power level I would suggest 1/4 inch dia. electrodes.  1/8th
>inch
>> may overheat to redhot on the electrode tips and cause poor quenching.
>> 
>> Resonance Research Corp.
>> www.resonanceresearch.com
>> 
>> 
>> ----- Original Message -----
>> From: "Tesla list" <tesla@xxxxxxxxxx>
>> To: <tesla@xxxxxxxxxx>
>> Sent: Tuesday, July 10, 2007 11:07 AM
>> Subject: RE: synchronous gap help (fwd)
>> 
>> 
>> >
>> > ---------- Forwarded message ----------
>> > Date: Tue, 10 Jul 2007 08:11:56 -0700 (GMT-07:00)
>> > From: penny831@xxxxxxxxxxxxx
>> > To: Tesla list <tesla@xxxxxxxxxx>
>> > Subject: RE: synchronous gap help (fwd)
>> >
>> > I have a related question on the propellor gap. I'm planning on
>pushing
>> > 15/120 through an .125 thoriated tungsten electrode. Is that to much
>power
>> > for such a small electrode? Your thoughts would be appreciated.
>> >
>> > -----Original Message-----
>> >>From: Tesla list <tesla@xxxxxxxxxx>
>> >>Sent: Jul 10, 2007 7:27 AM
>> >>To: tesla@xxxxxxxxxx
>> >>Subject: RE: synchronous gap help (fwd)
>> >>
>> >>
>> >>---------- Forwarded message ----------
>> >>Date: Tue, 10 Jul 2007 08:55:27 -0400
>> >>From: "Lau, Gary" <Gary.Lau@xxxxxx>
>> >>To: Tesla list <tesla@xxxxxxxxxx>
>> >>Subject: RE: synchronous gap help (fwd)
>> >>
>> >>I think you're going to run into a problem using your relatively
>small
>> >>teletype motor to spin-up such a heavy 3/8" thick disk.  I was
>barely
>> >>able to get such a motor to spin a 09" thick x 6.12" diameter G10
>disk
>> >>with just 4 brass acorn nuts electrodes, and it utterly failed to
>sync
>> >>with anything larger.  I'd strongly recommend using a propeller gap
>if
>> >>using a Teletype motor.  My SRSG page:
>> >>http://www.laushaus.com/tesla/sync_gap.htm, and Terry Blake's:
>> >>http://tb3.com/tesla/sparkgaps/index.html
>> >>
>> >>Regards, Gary Lau
>> >>MA, USA
>> >>
>> >>> ---------- Forwarded message ----------
>> >>> Date: Mon, 09 Jul 2007 23:59:58 +0000
>> >>> From: ameen_ghavam@xxxxxxxxxxx
>> >>> To: Tesla list <tesla@xxxxxxxxxx>
>> >>> Subject: synchronous gap help
>> >>>
>> >>>         I'm building a 240 bps srg for my tesla coil and was
>wondering
>> >>if
>> >>> anyone would give me any tips or suggestions. I'm planning to use
>a
>> >>3/8 "
>> >>> g10 rotor 8" in diameter with 4 1/4 " tungsten electodes held on
>with
>> >>> shaft collars (the disc is pinched between the collars). A sheet
>metal
>> >>> ring connects these electrodes. I have two stationary electrodes
>(one
>> >>> gap). My motor is a Teletype 1/12 hp motor, synchronous, and runs
>at
>> >>3600
>> >>> rpm. Any tips on how to balance, cut the g10 (i've heard its hard
>to
>> >>cut),
>> >>> motor arbor, or anything else I should know? Also, please email me
>off
>> >>the
>> >>> list. Thanks.
>> >>>
>> >>Cheers,
>> >>>
>> >>> Ameen Ghavam
>> >>>
>> >>
>> >>
>> >>
>> >
>> >
>> >
>> >
>> 
>> 
>> 
>
>
>