RE: [TCML] pole pig ballasting

["Jim Mora" <wavetuner@xxxxxxxxx>]

Hi Garry, all,

The best deal is to ship from a depot to a depot. I would bet the shipping
would be as much as the welder. I would put it on a pallet and take it to a
shipper though if you want it that bad. You might be better off search in
your area. Anyone near Southern Ca want it? I have a mongo Miller 300 amp
Miller from a School District now.

Jim Mora

-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On Behalf
Of garry neeley
Sent: Thursday, July 17, 2008 5:40 AM
To: Tesla Coil Mailing List
Subject: Re: [TCML] pole pig ballasting

I'm located in huntsville AL.  The pig is large but not as big as me.  It
stands about 4 feet and weighs over 600 lbs tho.  That lincoln would be
ideal but how much do you think shipping would be?

On Wed, Jul 16, 2008 at 11:03 PM, Jim Mora <wavetuner@xxxxxxxxx> wrote:

> Garry,
>
> Where are you located with that giant PIG, SOW that's the one that's
bigger
> than you yes? Anyway, I have a Lincoln Tombstone 225 which is old enough
to
> be copper wound - works great. I'll sell it for $75. It will tame that
> beast. Shipping is an issue these days! If you must drop the voltage, use
> the arc welder (in series of course) on the output of the variac if I
> remember correctly. I have several ballasts now. I sold my Thunderbolt
too.
> You could stack 3 of those variacs on the same shaft. Then we revisit the
> balancing chokes though. The Lincoln won't pass much more than 50-60 amps
> at
> full tilt though so 2 variacs would be ideal.
>
> I'm in So. Ca.
>
> Jim Mora
>
> -----Original Message-----
> From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On Behalf
> Of Jon Danniken
> Sent: Wednesday, July 16, 2008 1:37 PM
> To: Tesla Coil Mailing List
> Subject: Re: [TCML] pole pig ballasting
>
>  ----- Original Message -----
> From: "garry neeley"
> >>  Which brings me to the question,
> >> how could I ballast the pig to only draw 30 amps @240v.  (on a budget)
>
> Buy an 240VAC arc welder on Craigslist; around here they go for between
> $50.00 and $100.00.  If you get a Miller (Thunderbolt), it has an
> infinitely
>
> adjustable shunt, whereas the Lincoln ("tombstone") units just have
> different taps; you might find a Montgomery Wards or Century unit; they
> also
>
> work fine, and are often a lot cheaper due to not being a "brand" name.
>  The
>
> bonus is that you also get an arc welder to play around with.
>
> The way you hook it up is to short the "Work" and "Electrode" outputs on
> the
>
> front of the welder, then wire the 220VAC feeding the welder in series
with
> your variac.  Adjust the shunt or use a different tap until you get the
> required current limiting.
>
> Jon
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla